#Signal art reamp box how to
#Signal art reamp box manual
#Signal art reamp box portable

I turned on the outputs on the left side of the mixer. I told my DI guitar track to go out to Sub 1. I added a mono output in my I/O settings.

#Signal art reamp box how to

One video the guy doesn't even talk about routing the signal.Īnother video the guy does some things like switching the headphones to outputs 3+4 (which I don't know how to do on mine? nor do I think it should even be necessary?) but otherwise I followed him to a tee and nothing happened.

I've watched a few and none were helpful-hence why I came here in the first place. Have you tried putting say an active bass through it as a DI box?ĭarrenporter1 wroteThere are several S1 specific videos on YouTube pertaining to reamping. There are a few videos on reamping with Studio One on YouTube. From that output on the interface, you go into the reamp box. Finally, you just send your dry DI guitar track to that output. Then you need to make sure your interface outputs are assigned as outputs in Studio One. I also have other Radial products and they are fantastic too so you can't go wrong with either one. lol.įWIW, I use the ART device and it works great. There are more expensive ones too if you are into paying more than you have to. You really need a reamping box so your pedalboard and/or amp see the correct loads that they would expect seeing from a guitar. To the OP as long as the signal coming in from the microphone is not input monitor enabled in Studio One and feeding the same output that is being sent to the amp you won't have any feedback issues.ĭarrenporter1 wroteTo do it correctly there is more to it than just making sure your levels are ok. And provide some tonal options like low and high end cut filters etc.īut overall re-amp boxes are a good thing and will ensure the best possible result from doing this. Some re-amp boxes go a little further and simulate the equivalent circuit of a guitar as well. Isolation and ground lift options will also prevent the guitar amp from getting an earth loop type hum which can also be a problem. Input stages of the guitar amp can then be set for more normal operation. An adjustable output level is also a good thing allowing you to fine-tune the level going into the guitar amp. So a good re-amp box is going to provide that level shift downwards. one is 600 ohms and the other is several hundred K ohms usually) (using a passive DI in reverse while offering a good impedance match can actually step the signal up from the interface due to the transformer windings not being the same. Some interfaces can output + 4 dBu at the ref level where as many guitar amps are sensitive and might only be expecting signals as low as -20 or even lower. Try a 1/4 cable from the interface out to the amp, do you hear it better than with the RMP in the chain? If you do then probably you need to look at your cable wiring.Īnother option is to try a DI box in reverse and see how it fares or get the active reamp box.One of the main concerns you will have feeding the output of an audio interface directly into a guitar amp will be a serious level mismatch. Pin 1 of the XLR will go to the sleeve of the TRS jack.

Pin 3 of the XLR will go to the Ring of the TRS jack Pin 2 of the XLR will go to the Tip of the TRS Jack So maybe something wrong with your cable? I remember I had to get buy special cable or you can make yours, this is what Radial told me via email when I asked them about the wiring of the interface out to the reamper input:

#Signal art reamp box manual

With the Edirol I added a Art Tube MP preamp to raise the level but that most likely raised the noise floor.Ĭheck your interface's manual and look for a setting on the mixer software probably or on the unit itself to switch between -10dbu and +4dbu if possible.ĮDIT: Check Focusrite's site and they give I think my PreSonus FP10 is +4dbu and that works fine.

#Signal art reamp box portable

I had the same issue with my portable interface Edirol/Cakewalk UA-4fx and its specs say output level is -10 dBu. The RMP is passive so that means that your output is probably below level of what you need.